Skip to content
Black steel driveway gate with one leaf taken off its hinges and laid on wooden blocks beside an open red toolbox and a moving blanket

Gate Repair in San Antonio

Most gates that misbehave are not worn out. They have a part that has slipped, bent or worn down: a hinge that has loosened its grip on the post, a roller with a flat spot, a track kinked by a tire, a safety sensor knocked out of line. Gate repair finds that part and puts it right, so the gate opens, closes and latches the way it did when it was new.

The work covers swing and slide gates on driveways and property entrances, manual or automatic, in steel, aluminum, wrought iron and wood.

Signs a Gate Needs Repair

  • The gate drags on the ground or the drive, or needs a lift to close.
  • It sags at the latch end, so the leaves no longer meet level.
  • It will not latch, or only latches with a push.
  • It swings or slides unevenly: fast in one spot, sticky in another.
  • It makes grinding or scraping noises as it moves.
  • It hangs off its post, or a hinge has pulled loose.
  • A panel, picket or rail is bent or broken.

If you are not sure which of these you are looking at, the signs and symptoms match what you notice to a likely cause and how soon it needs attention.

Where the Trouble Usually Starts

Tall black vertical-board double gate with two lever handles in a matching fence, packed dirt and broken concrete in front

On a swing gate the weight hangs from the hinge side, so that is where sagging begins. A post that leans a few degrees drops the far end of the gate by inches. In San Antonio’s clay soils, a footing that was set shallow can shift as the ground swells after rain and shrinks in a dry spell, which tips the post with it. The fix is to reset or brace the post first, then deal with the hinges.

On a slide gate the trouble is usually lower down. Rollers and guide wheels wear flat, the track collects gravel and leaves, and a car tire can put a kink in the rail. A stalling slide gate is more often one of those than a bad motor, so the rollers and track get checked before anyone blames the opener.

Latches fail mostly because the gate has moved, not because the latch broke. Once the gate hangs true again, the latch can be lined up so it catches without a shove.

What Gets Repaired

Gate parts, what they do and how they fail
Gate partWhat it doesHow it fails
HingesCarry a swing gate’s weight and let it pivotWear, loosen at the bolts, pull out of the post; the gate sags
Hinge post and footingHold the gate plumbLean or shift as soil moves; the latch end drops
Rollers and guide wheelsCarry and steer a slide gateWear flat, seize or crack; the gate grinds or stalls
TrackGives a slide gate a straight pathBends, fills with debris, breaks loose from the concrete
Latch and keeperHold the gate shutFall out of line as the gate moves, wear or break
Safety sensors (photo eyes)Stop an automatic gate from closing on a car or personGet knocked out of line or dirty; the gate refuses to close
Frame, panels and picketsGive the gate its shape and strengthBend in an impact, rack out of square, rust at the joints

Some of these parts belong to the opener as much as the gate. When the trouble turns out to be the motor or its controls, the job moves over to gate opener repair.

Repair Basics, Answered

Can a sagging gate be fixed?

Usually, yes. A swing gate sags when its hinge post leans, its footing shifts, the hinges wear or the frame racks out of square. Resetting or bracing the post, replacing worn hinges and squaring the frame bring the latch side back up. A frame that is rusted through at the joints is the exception, because there is nothing solid left to pull square.

What causes a gate to stop latching?

Most often the gate has dropped or shifted, so the latch and its keeper no longer line up. Loose hinges, a leaning post or a worn latch can do it, and so can a slide gate that stops short of its catch because of a dirty track or a tired limit switch on the opener. Re-aligning the latch alone only hides the cause.

Can part of a gate be replaced instead of the whole gate?

Yes. Hinges, rollers, guide wheels, a section of track, latches, safety sensors and bent pickets or panels can be swapped on their own. Matching an older ornamental pattern exactly is not always possible, so a panel replacement may look slightly different from the rest of the gate.

Repair or Replace?

The questions that decide it

  • Is the frame still solid, or rusted through or rotted at the joints?
  • Is this the first repair, or the same problem coming back again?
  • Does the gate still suit the driveway and the way you use it?
  • If you want an opener someday, can this gate carry one?

A sound frame with a worn part is a repair. A frame that is failing, a fix that keeps coming back or a gate that no longer fits its job points toward a new gate. Either way, you should hear what was found and why before any part comes off.

Black board double gate with lever handles closing off a gravel parking pad beside a house
Black horizontal-slat swing gate with a drop-rod latch and a slide bolt, matching slatted fence beside it
Black horizontal-board side gate with a lever handle set between matching fence panels beside a house, a lawn in front

Get the Gate Working Again

Describe what the gate is doing and send it over, or call and talk it through.

Call (726) 213-6879