Skip to content

Gate Questions

Gate questions with plain answers, grouped by the kind of work they concern: choosing a service, repairs, new gates, openers, access systems, upkeep, describing trouble and the visit itself.

Choosing the Right Service

Which service fits my situation?

If the gate is up and misbehaving (it drags, sags, sticks or will not latch), start with repair. If it moves freely by hand but the motor stalls, hums or reverses, the opener is the likely culprit. Keypads, remotes, intercoms and card readers fall under access control. No gate yet, or a frame that is past saving, means installation. A gate that still works but squeaks, slows or needs a shove is due for maintenance.

Should I repair the gate or replace it?

Repair makes sense when the frame is sound and the trouble is a part: a hinge, a roller, a bent track, a latch or a safety sensor. Replacement is worth a look when the frame is rusted through or rotted, the same repair keeps coming back, or the gate no longer suits the driveway or cannot carry an opener.

What should I have ready before I call?

Know whether the gate swings or slides, roughly how old it is, and what it does and when: every time, only when hot, only in the morning. If the opener or keypad has a brand name on it, jot it down. A couple of photos of the hinges, the track or the motor box help too.

Is it safe to keep using a gate that will not close properly?

A gate that hangs off a post, drops into the drive or reverses without reason should be left alone until it is checked. Put it in manual mode with the release if it has an opener, and keep people and cars clear of its path.

Do you work on business and neighborhood entrances?

Yes. Small businesses and neighborhood associations call when an entrance gate has to open and close reliably all day, and the work covers their operators, keypads, intercoms and card readers as well as the gates themselves.

Repairs

Can a sagging gate be fixed?

Usually, yes. A swing gate sags when its hinge post leans, its footing shifts, the hinges wear or the frame racks out of square. Resetting or bracing the post, replacing worn hinges and squaring the frame bring the latch side back up. A frame that is rusted through at the joints is the exception, because there is nothing solid left to pull square.

What causes a gate to stop latching?

Most often the gate has dropped or shifted, so the latch and its keeper no longer line up. Loose hinges, a leaning post or a worn latch can do it, and so can a slide gate that stops short of its catch because of a dirty track or a tired limit switch on the opener. Re-aligning the latch alone only hides the cause.

Can part of a gate be replaced instead of the whole gate?

Yes. Hinges, rollers, guide wheels, a section of track, latches, safety sensors and bent pickets or panels can be swapped on their own. Matching an older ornamental pattern exactly is not always possible, so a panel replacement may look slightly different from the rest of the gate.

New Gates

Should I choose a swing gate or a slide gate?

Let the site decide first. A swing gate needs clear, fairly level ground inside its arc, and a slide gate needs a clear run beside the opening at least as long as the gate. If the drive rises from the street or the arc would reach a parked car, a slide gate usually wins; if there is no room beside the opening, a swing gate does.

Can an opener be added to a new gate later?

Yes, if the gate is built with one in mind: a frame stiff enough to be pushed from one point, posts and hinges or rollers sized for the extra load, and conduit for the wiring laid under the drive before the concrete goes down. A gate built that way can take any of the usual gate openers later without cutting into a finished drive.

Do neighborhood or HOA rules apply to a new gate?

They can. Some neighborhood associations set rules on a gate’s height, style, color or how far it sits from the street, and a city may have its own rules for gates and fences along a street. Check with the association, and with the city where it applies, before the design is final.

Openers and Motors

What should I do with an automatic gate in a power outage?

Many openers simply stop where they are when the power goes out. If yours has battery backup, it keeps running for a limited number of cycles; if not, use the manual release to move the gate by hand. Lock the release again once power is back, so the opener holds the gate and drives it as before.

What is the manual release on a gate opener?

It is a lever, knob or keyed lock that disconnects the motor from the gate, so the gate can be pushed by hand. On a swing operator it usually sits on the arm, and on a slide operator it is on the motor housing. If yours takes a key, keep the key where everyone who uses the gate can find it.

Can an older manual gate be automated?

Often, yes, if it swings or rolls easily by hand, hangs level and is strong enough for an operator’s push, with power run to it. A gate that drags, sags or flexes has to be put right first, and some light ornamental or wood gates need bracing before an arm can move them. When the old gate cannot take an opener, a new gate built for one is the better route.

Keypads, Remotes and Intercoms

Is a keypad or a remote better for my gate?

Many gates use both. Remotes suit the people who drive through every day, since the gate starts opening before the car reaches it, while a keypad lets guests and service visits in without handing out hardware. Where visitors arrive often and someone should decide who comes in, add an intercom or a call box.

How many users can a gate access system hold?

It depends on the system. Every keypad, receiver and card reader has its own memory limit, and basic home units hold far fewer codes and remotes than systems built for businesses and associations. If an entrance is running out of room or expects to grow, a controller with more memory, or one managed from a computer or phone, may fit better.

What should I do about a lost or stolen remote?

Have it erased from the receiver so it no longer opens the gate. If the receiver cannot remove one remote on its own, clear its memory and pair the remotes you still have. If a keypad code could have gone with it, written down in the same car for example, change the codes too.

Upkeep

How often should a gate be looked at?

It depends on how hard the gate works. A driveway gate that opens a few times a day wears slowly, while a neighborhood or business entrance that cycles hundreds of times a day wears far faster. A common rule of thumb in the trade is a check at least once a year, and more often for heavy use. A storm, a bump from a car or a new noise is a reason to have it looked at sooner.

What can I clean on the gate myself?

With the opener switched off, sweep or blow leaves, gravel and grit out of a slide gate’s track, and wipe the safety sensor lenses with a soft dry cloth. Wash the frame with mild soap and water, and touch up chipped paint before rust gets under it. Keep grease and oil off the track itself, where they hold grit, and never spray anything into the opener’s housing.

Which problems should not wait for routine maintenance?

A gate that hangs off a hinge, has dropped off its track, reverses on its own or fails to stop when something is in its way needs attention before anything else. So do sparks or a burning smell at the opener, and a grinding of metal on metal. Switch the opener off, keep people and cars clear, and call rather than waiting for the next visit.

Describing Gate Trouble

What will a technician want to know about the noise?

What it sounds like (a grind, a squeal, a click, a hum or a bang), where it seems to come from (the hinges, the track or the opener’s housing) and when it happens: as the gate starts, partway or at the end of its travel. Say whether the noise is new or has been building for a while. A hum with no movement points somewhere quite different from a grind while the gate moves.

Should I note the opener’s lights or beeps?

Yes. Many openers flash a light or beep in a set pattern to report a fault, such as a blocked sensor, a limit problem or a low battery, and photo eyes often carry a small indicator light that shows whether the pair can see each other. Count the flashes or beeps and note any lights you can see without taking a cover off. Do not open the control box to look.

Does the time of day or the weather matter?

Often, yes. A gate that binds only on hot afternoons may be steel expanding in San Antonio’s summer heat until it rubs its latch or stop. Trouble after heavy rain can point to water inside a keypad, or to a footing that moved as the clay soil swelled. A gate that acts up at the same hour each day may have low sun shining straight into a photo eye.

Should I mention anything that changed recently?

Yes, because a recent change is often the cause. A storm or a power outage can bring a surge that damages a control board, and a bump from a car or a mower can bend a track or knock a sensor out of line. New planting can grow into a photo eye’s beam, and digging for irrigation or landscaping can cut the low-voltage wires that run to keypads and sensors.

How do I describe a gate problem if I do not know the parts?

Say what you see and hear in plain words. "The gate stops halfway and backs up," "it grinds near the end of the track" or "the left leaf hangs lower than the right" tells a technician more than a guess at the cause. Note whether it happens every time or only now and then.

Should I try to fix it before I write in?

Clearing leaves or gravel out of a slide gate’s track is fine, and so is wiping a dusty safety sensor lens. Leave springs, hinges under load, wiring and the opener’s settings alone: a heavy gate can drop or swing without warning when the wrong part is loosened.

Can I send photos or a short video?

Send them by email once the form is in. A wide shot of the whole gate plus close views of the hinges, the track or rollers and the opener box show a lot, and a short clip of the gate stalling or reversing is even better.

The Visit

Do I need to be home while the work is done?

It helps to be there at the start, to show what the gate does and where its power switch is, and at the end, to see it working and take back the remotes and codes. Whether the rest can go ahead without you depends on the job and on access to the gate and its power, so settle that when the visit is arranged.

How is the property kept secure while the gate is out of use?

Generally, a gate is left in the safest state the job allows: closed and latched, or secured open when cars have to get through. If a leaf has to come off or a part is on order, ask how the opening will be closed off in the meantime. Tell everyone who relies on the gate, so nobody counts on it being locked.

Can deliveries and visitors still get in?

Usually, with some planning. A gate in manual mode opens by hand, and a gate secured open lets cars through. If a keypad, intercom or call box is being replaced, tell regular visitors and delivery drivers how to reach you until it works again.

Where the Work Is

My neighborhood is not listed. Can you still come out?

It may well be in reach. The communities in the table are examples rather than a boundary, and San Antonio itself is the base. Send the street and ZIP code with your request, or ask on the call, and you will hear whether the address is covered.

Does the ZIP code or the community name matter more?

The ZIP code and the street together are the surer guide, because community names and ZIP codes do not line up neatly. Olmos Park and Monte Vista share 78212, for example, and Alamo Heights and Terrell Hills share 78209. Give both if you know them.

Can I ask before sending the request form?

Yes. Call and ask whether your address is covered before you fill anything in. You can also ask in writing when you Schedule Service, along with a line about what the gate is doing.

The gate is at a property I do not live at. Which address counts?

The gate’s address. Give that street and ZIP code, plus a way to reach whoever can open the property and approve the work, such as a tenant, a property manager or an association board member.

Still Wondering About Your Gate?

Ask about the gate in front of you: describe it in the request, or call the shop.

Call (726) 213-6879