Gate Terms Glossary
Gate work comes with its own vocabulary. On the phone you may hear that the operator is fine but a limit switch has slipped, or that the photo eyes need lining up, and it helps to know what those words mean before you decide anything.
Most of the words fall into four groups: the gate itself, the opener that moves it, the keypads and remotes that let people in, and the safety devices that keep it from closing on a person or a car.
Search the Terms
Gate Term Filter
Narrow the terms by a word, a first letter or a group.
First letter
Type a word, pick a letter or choose a group
Gate Terms, A to Z
| Term | Plain-words meaning | Where you would notice it |
|---|---|---|
| Auto-reverse | The opener’s safety response: when a closing gate meets resistance or a sensor is tripped, it stops and backs away. | A gate that bounces back halfway, or does not when it should |
| Battery backup | A battery in or beside the opener that keeps the gate running for a while when the power goes out. | Slow movement or warning beeps after an outage |
| Cantilever gate | A slide gate that hangs from rollers on posts beside the opening and never touches the ground, so it needs no track. | Gravel drives, uneven ground and commercial entrances |
| Card reader (fob) | A reader on a post that opens the gate when someone holds up a programmed card or key fob. | Business, apartment and neighborhood entrances |
| Control board | The circuit board inside the opener that takes signals from remotes, keypads and sensors and tells the motor when to run. | An opener that stops responding after a storm or a surge |
| Drop rod | A sliding rod on one leaf of a double gate that drops into a hole or sleeve in the drive to hold that leaf still. | Double gates whose leaves no longer meet or stay put |
| Edge sensor (safety edge) | A soft strip along the gate’s leading edge that stops and reverses the gate when it presses against something. | The front edge of slide gates and busy commercial gates |
| Exit wand | A sensor buried beside the drive, inside the gate, that picks up a car’s metal as it leaves and opens the gate with no remote or code. | Entrances that let drivers out without pressing anything |
| Footing | The concrete base that holds a gate post in the ground; when it shifts, the post leans and the gate follows. | A leaning post, or a gate that sags after a very wet or very dry spell |
| Gate stop | A post, bracket or bumper that marks the end of the gate’s travel and takes the knock when the gate gets there. | Gates that swing too far, or bang as they finish |
| Gooseneck post | A curved post that holds a keypad, card reader or intercom out at a driver’s window height. | Beside the drive, a little ahead of the gate |
| Guide rollers | Pairs of wheels on a post that keep a slide gate upright and steer it as it rolls. | At the top of a slide gate, where it passes its post |
| Hinge | The pivot a swing gate turns on; it carries the gate’s weight as well as letting it move. | Squeaks, rust, or a gate that drops at the latch end |
| Hinge post | The post the hinges are fixed to. It takes the whole load of the gate, so it has to stay plumb. | A gate that sags even though its hinges are sound |
| Intercom | A call box at the gate that lets a visitor talk to someone inside, who can then open the gate; some add video. | Visitor entry at homes and shared entrances |
| Keypad | A pad of numbered buttons that opens the gate when someone enters the right code. | On a post by the drive or beside a walk gate |
| Latch and keeper | The latch holds the gate shut; the keeper is the catch on the post or the other leaf that it locks into. | A gate that will not stay shut, or needs a push to catch |
| Limit switch | A switch, or a setting on the control board, that tells the opener where fully open and fully closed are. | A gate that stops short or runs past where it should |
| Linear actuator | A swing gate opener shaped like a long arm or ram that pushes the leaf open and pulls it shut. | Mounted along a swing gate, from the post to the leaf |
| Loop detector | A unit in the opener that reads a wire loop buried in the drive and senses a car above it, to open the gate or keep it from closing. | Thin, sealed saw cuts in the pavement near the gate |
| Manual release | A lever, knob or keyed lock that disconnects the opener so the gate can be moved by hand. | During a power outage, or when the opener breaks down |
| Operator | The trade word for an automatic gate opener: the motor, gearbox and controls that move the gate. | The arm or the box beside the gate |
| Photo eye | A sensor that sends an invisible beam across the opening to a receiver or reflector; if something breaks the beam, a closing gate stops or reverses. | Small boxes on posts either side of the drive |
| Rack and pinion | The drive on a slide gate opener: a toothed rack fixed along the gate, driven back and forth by a small gear, the pinion, on the motor. | Along the bottom rail of an automatic slide gate |
| Receiver | The radio unit in or beside the opener that listens for remotes and tells the opener to move. | A remote that works only up close, or not at all |
| Remote (transmitter) | The hand-held button that sends a coded radio signal to open or close the gate. | On a key ring or clipped to a car visor |
| Roller (V-groove wheel) | A wheel a slide gate rides on; the V-groove kind has a notch that runs along a ridged track. | Grinding, stalling, or a gate that rides unevenly |
| Slide gate | A gate that rolls sideways across the opening instead of swinging, on a ground track or as a cantilever. | Short or sloping drives, and drives close to the street |
| Swing gate | A gate that opens on hinges, as a single leaf or a matching pair. | Drives with room for the leaves to swing clear |
| Track | The steel rail set in the ground that a slide gate’s wheels run along. | Leaves and grit packed into it, or a bend that makes the gate grind |
If you know what the gate is doing but not which part is to blame, its signs and symptoms point to the likely cause.
Words That Get Mixed Up
A few pairs of words are easy to confuse on a first call:
- Opener and operator. The same machine. “Operator” is the trade word; “opener” is the everyday one.
- Photo eye and safety edge. Both stop a closing gate. A photo eye watches a beam across the opening; a safety edge is a strip on the gate that reacts when it touches something.
- Remote and receiver. The remote sends the signal and the receiver, in or beside the opener, listens for it. When a remote works only up close, either one can be at fault.
- Hinge and hinge post. The hinge is the pivot; the post is what it is fixed to. A sagging gate can come from either, and the fixes are quite different.
- Limit switch and auto-reverse. Limits tell the opener where to stop at the end of its travel; auto-reverse turns the gate back when it meets resistance on the way. A gate that stops in the wrong place points to the limits, and one that turns back halfway points to the safety system or the force setting.
Get the Faulty Part Checked
Once you know which part is acting up, send the details or call the shop to have it looked at.