Skip to content
Dark composite-panel slide gate in a black steel frame running on a track along a paved alley drive

Our Process for Gate Work

Most people call a gate company only now and then, when a gate has stopped behaving or when they want one they do not have yet. Either way, the job tends to follow the same path.

A swing gate that drags is a different visit from a new keypad at a neighborhood entrance, but the order mostly holds, and knowing it takes some of the guesswork out of a first visit.

Stages of a Gate Job

Technician kneeling at an open gray control box on a post beside a slide gate, checking a terminal with a screwdriver

Every job differs in its details, but most run in this order.

  1. First call. You describe the gate and what it is doing: swing or slide, manual or automatic, what you notice and when it started. Those answers often narrow the trouble down before anyone drives out. Call, or send the details through Schedule Service, and a time is settled to come and look at the gate.
  2. Looking at the gate. The gate is run by hand and, if it has one, by its opener. A careful look covers the whole gate (hinges or rollers, track, posts, latch, sensors and controls), because the part that complains is not always the part that failed. The crew explains what they found and why before touching a part.
  3. Agreeing the work. Next comes a plain conversation about the options: what fixing the problem involves, whether a worn part can be repaired or should be replaced, and when a new gate is worth considering. You decide what goes ahead.
  4. Parts and scheduling. Many repairs use common parts such as rollers, hinges, latches and sensors. Others need a part made for one particular operator or gate, such as a control board or a motor, which may have to be ordered before the work can be finished.
  5. The work itself. Depending on the job, posts are reset or braced, hinges and rollers replaced, tracks straightened, worn operators swapped and keypads wired in. The gate is usually out of use for part of the visit, and power to an opener is normally switched off while it is worked on.
  6. Testing. Before a job is called finished, the gate is cycled again and again, its path is blocked to test the auto-reverse, the latch and the manual release are checked, and every fastener is tightened once more. New crew members begin by watching these checks, then run them on small repairs.
  7. Handover. You see the gate open, close and latch, hear what was done, and have the remotes and codes back in hand. It is a good moment to try the manual release yourself, so you know how to open the gate by hand if the power goes out.

If a part has to be ordered

Generally, a part that is not on hand is ordered and the job is finished once it arrives. Until then the gate is made as safe and usable as the situation allows: switched to manual so it opens by hand, or secured open or closed, whichever the property needs. Ask how to use the gate in the meantime, and keep people and cars clear of anything left apart.

While the Gate Is Down

Black steel driveway gate with one leaf taken off its hinges and laid on wooden blocks beside an open red toolbox and a moving blanket

Some repairs take a gate out of service for a while. A leaf may come off its hinges to be squared up on blocks, a post may be reset, or an opener may be disconnected while its replacement goes in.

For a home, that usually means a driveway left open, or closed and opened by hand, until the work is done. For a small business or a neighborhood entrance, it can mean planning how staff, residents and visitors get in. It is worth settling that before the work starts.

Do I need to be home while the work is done?

It helps to be there at the start, to show what the gate does and where its power switch is, and at the end, to see it working and take back the remotes and codes. Whether the rest can go ahead without you depends on the job and on access to the gate and its power, so settle that when the visit is arranged.

How is the property kept secure while the gate is out of use?

Generally, a gate is left in the safest state the job allows: closed and latched, or secured open when cars have to get through. If a leaf has to come off or a part is on order, ask how the opening will be closed off in the meantime. Tell everyone who relies on the gate, so nobody counts on it being locked.

Can deliveries and visitors still get in?

Usually, with some planning. A gate in manual mode opens by hand, and a gate secured open lets cars through. If a keypad, intercom or call box is being replaced, tell regular visitors and delivery drivers how to reach you until it works again.

Before the Technician Arrives

A little preparation saves time once someone is standing at the gate. Most of it comes down to room to work, safety and information.

Room to work means the gate’s whole swing or slide path is clear, with cars moved out of the drive and nothing parked across the track. Safety means pets are inside and children know the gate is off limits while it is worked on. Information means a note of when the trouble shows up, and knowing where the remotes, codes and any release key are kept.

Timing matters more than it seems. In San Antonio’s summer heat, steel expands as it warms, so a gate that binds only in the late afternoon is worth mentioning, and so is one that drags only after a heavy rain.

If several people use the gate, tell them a visit is coming, so nobody tries to drive through in the middle of a repair.

Visit Prep Checklist

Tick each item as it is done, then check the list to see what is still left.

Before the visit

Tick what is done

Then press Check My List to see what is still left.

Set Up the First Visit

Every job starts with a call or a short request that says what the gate is doing.

Call (726) 213-6879